おまえの hddparm -tT 教えてください。at LINUX

---

116:login:Penguin
02/11/30 17:27 nYKSk4oQ
>>107
それは、-Tの数値を理解していないと思われ。
manにもわりと詳しくかいてある。読め。



117:login:Penguin
02/11/30 21:31 JMRKhfk5
ヲレも2.4.19のときDMA onに出来なかったのでパッチあてたよ
2.4.20でカーネル作り直したら，そのままでDMA使用できた．


118:login:Penguin
02/12/05 20:20 /JxgZHh9
ケーブルがふるいタイプのものだと、実力が出せなかったりするし、
なぜかしらないがVine2.5だと、/etc のしたにあるコンフィグレーション
ファイルでDMAをオンにしないと、デフォルトではPIOでHDDがつながっている。

119:login:Penguin
02/12/05 21:10 wucIOqMw
>>118
どのファイルですか? fstab? 俺もしかしたらそれに当っているかも知れない。

120:login:Penguin
02/12/05 21:18 Pb7L1Rez
>>119
/etc/sysconfig/harddisks

121:login:Penguin
02/12/05 22:21 wucIOqMw
>>120 サンクス。たしかに comment out されてるね。しらんかった。安全の為らしいが。

122:login:Penguin
02/12/07 07:51 Rp8fwyVN
ここはpureIDE限定デスカー？
昔，Escaladeで計ったら-tで80Mぐらい出たような…

>>105
pupu.
strerror()がSUCCESS（藁

>>114-117
そういうのは大概，パッチ無くともDeviceID書き加えるだけでOKと成り候。

123:117
02/12/07 09:18 UnOGrCiZ
>>122
チップセットが新しい場合でも？
ちなみに自分の場合は845Gだったんだけど
パッチ当てる，もしくは2.4.20でカーネルをつくり直さないと
DMAをONに出来なかった．
時間があればDeviceIDをどのように書き加えればいいのか
ポインタだけでもいいから教えて.

124:名無しさん＠Ｅｍａｃｓ
02/12/08 01:40 3ofuvD+J
VIA の VT82* チップの載ったマザーを使っているんだけど、
どうしても udma3/4/5 が有効にならないんです。

2.4.20 に ac パッチ当てて使ってみてるんですが。
それとも何かカーネルの設定で必要な項目とかあるのですかね。

ポインタでも良いのでどなたかお助け～。

125:名無しさん＠Ｅｍａｃｓ
02/12/08 01:43 cqe9VQcn
>>124
/proc/ide/via きぼん

126:124
02/12/08 13:24 3ofuvD+J
こんなかんじです。

----------VIA BusMastering IDE Configuration----------------
Driver Version: 3.35-ac
South Bridge: VIA vt82c686a
Revision: ISA 0x1b IDE 0x6
Highest DMA rate: UDMA66
BM-DMA base: 0xd000
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: no no
Post Write Buffer: no no
Enabled: yes yes
Simplex only: no no
Cable Type: 40w 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: DMA PIO DMA PIO
Address Setup: 30ns 120ns 30ns 120ns
Cmd Active: 90ns 90ns 90ns 90ns
Cmd Recovery: 30ns 30ns 90ns 90ns
Data Active: 90ns 330ns 90ns 330ns
Data Recovery: 30ns 270ns 90ns 270ns
Cycle Time: 120ns 600ns 180ns 600ns
Transfer Rate: 16.6MB/s 3.3MB/s 11.1MB/s 3.3MB/s


127:124
02/12/08 13:26 3ofuvD+J
ちなみに hdparm -i はこんな具合です。

/dev/hda:

Model=DupliDisk IDE RAID-1 Adapter( 1.27), FwRev=VA2OA50K, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-

DupliDisk IDE RAID-1 Adapter の先にATA100対応のディスクが付いてます。
DupliDisk って製品は ATA66 対応を謳ってるRAIDコントローラです。


128:124
02/12/08 13:57 3ofuvD+J
今気づいたんですが、Cable Type が 40w として認識されて
しまってるのが原因っぽいですね。Dupli Diskに付属のケーブル
を使っているのですが、マニュアルに通常のATAケーブルじゃ駄目だ
と書いていたので素直に従ってるんですけどね。

一応、製品仕様には 80wire - 40pin Connector とあります。


129:名無しさん＠Ｅｍａｃｓ
02/12/08 14:31 cqe9VQcn
もしかすると、カーネルの問題かもしれず。

/usr/src/linux/drivers/ide/via82cxxx.c

の中で、無条件に via_80w に 0 を入れている場面があれば、犯人はカーネルです。
変なパッチが当てられてると思うので、そのパッチを抜いて再構築ですな。

# ちなみに、Vine-2.5 の　kernel-2.4.18-0vl3 はその問題を抱えてました。



130:login:Penguin
02/12/08 20:26 BfVBUrNL
>>123
最高に手抜きな方法。
まったくの新設計チップだとちと困るが，同系統のチップが以前にある場合…
2.4系カーネルなら
linux/include/pci_ids.h
にある同系統チップのDeviceIDを自前のものに書き換える。

845GのICH4ならICH3のDeviceIDを置き換えてしまうといいだろう。

131:117
02/12/11 21:19 ID6Nerw+
>>130
どうも
でも、厨なんでいまいちよく分からない、もうちょっと教えとくれ
dmesg見たら
---------------------------
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
.......
i810: Intel ICH4 found at IO 0xe400 and 0xe000, IRQ 11
.......

のように書かれていたので
pci_ids.hの
#define ....INTEL_82801BA_[0-9] hoge
のところの hogeの値を 0xe400 0xe000とかに替えて
カーネル作りなおしたらいいの?



132:123
02/12/12 08:41 8b2/Odzj
のぉ、厨にわかるよう説明するの下調べが面倒臭い。。。


133:123
02/12/12 22:02 8b2/Odzj
自分のIDEコントローラの調べ方：
* PCI_IDE: unknown IDE controller on PCI bus xx device xx, VID=xxxx, DID=xxxx

対応してない(unknown)なコントローラなら、VID=xxxx DID=xxxx として
Vendor、Deviceの各IDが表示される。

置換元のDeviceの調べ方:
linux/drivers/pci/pci.ids
や
URLﾘﾝｸ(pciids.sf.net)
を見て、旧世代のIDEコントローラのIDを探す。

* (VID)8086 (DIV)244b (Desc.)82801BA IDE U100

今回はこのICH2 UDMA100コントローラを生贄にしてみようか。

実際に置換する：
linux/include/linux/pci_ids.h内で、先の置換元を探すと

#define PCI_DEVICE_ID_INTEL_82801BA_9 0x244b

とある。これを書き換え。
#define PCI_DEVICE_ID_INTEL_82801BA_9 0xXXXX
(DID:244b->XXXX)
とすれば良い。

134:117
02/12/12 22:23 Y87YP1b7
>>133
どうもありがと
少し賢くなったよ.
123=117だよ




135:偽123
02/12/12 22:53 8b2/Odzj
あ、122だった。
番号一つ間違えター。
逝っときます。

136:login:Penguin
02/12/15 21:11 OrfgqvVw
/dev/hda:

Model=Maxtor 4D080K4, FwRev=DAH017K0, SerialNo=D4H07X8E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160086528
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-6 T13 1410D revision 0 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.36 seconds =355.56 MB/sec
Timing buffered disk reads: 64 MB in 1.88 seconds = 34.04 MB/sec

137:login:Penguin
03/01/07 13:26 PhwXegwZ
結果が変なので困ってる。なんでだろ。UDMA66なのに遅過ぎる。変なメッセージは出るし。

# hdparm -i /dev/hda

/dev/hda:

Model=WDC WD205BA, FwRev=16.13M16, SerialNo=WD-WM9490076499
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40088160
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled

# hdparm -Tt /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 4.33 seconds = 29.56 MB/sec
Timing buffered disk reads: 64 MB in 3.65 seconds = 17.53 MB/sec
Hmm.. suspicious results: probably not enough free memory for a proper test.


138:IP記録実験
03/01/08 22:11 1aQvEFST
IP記録実験
ｽﾚﾘﾝｸ(accuse板)

1 名前：ひろゆき ◆3SHRUNYAXA ＠どうやら管理人 ★ 投稿日：03/01/08 17:13 ID:???
そんなわけで、qbサーバでIPの記録実験をはじめましたー。

27 名前：心得をよく読みましょう 投稿日：03/01/08 17:20 ID:yL/kYdMc
SETTING.TXT管轄でないということは全鯖導入を視野に、か？

38 名前：ひろゆき ◆3SHRUNYAXA 投稿日：03/01/08 17:22 ID:rLfxQ17l
>>27
鋭いです。

73 名前：ひろゆき ◆3SHRUNYAXA 投稿日：03/01/08 17:27 ID:rLfxQ17l
＞ところで、IPが抜かれて何か今までと変わることってあるのでしょうか？
・今までより、サーバが重くなる。
・裁判所や警察からの照会があった場合にはIPを提出することがある。

139:login:Penguin
03/01/09 01:24 CPz3YJ5L
ひろゆきって男前だよな

140:login:Penguin
03/01/09 01:34 CPz3YJ5L
>>440
そんなに寄付集まらないと思うぞ。
利用者に月１万円って現実的ですか？

141:login:Penguin
03/01/09 02:08 WLJuqPrv
Σもろふしあなさん！？>>535

142:login:Penguin
03/01/09 03:02 HWqNEQq0
匿名とは、自分が提示する情報だけで勝負することをいうので、

143:login:Penguin
03/01/09 03:50 WLJuqPrv
>>169

　　マスコミだって商売だから、最終的には保身に走る。
　　政治屋なんかもっと怪しいじゃん（ｗ。

　個人情報保護法案の時にも、一番ウハウハなのは汚職しまくりで崖っぷちの政治屋だなんて
言われてたよね。

　まぁ、ぴろゆきの個人サイトだから・・・と言われれば２ちゃんにそこまで社会的意義を
求めるのも酷なんだろうけどさ（ｗ。

　これからは豚キムの事を、「親愛なる指導者同志」って書かなければ、聡連から命を狙われる
かと思うと（（（（ ;ﾟДﾟ）））ｶﾞｸｶﾞｸﾌﾞﾙﾌﾞﾙ

　でつな（ｗ。


144:login:Penguin
03/01/10 08:55 CqGam1as
Timing buffer-cache reads: 128 MB in 0.48 seconds =266.67 MB/sec
Timing buffered disk reads: 64 MB in 1.59 seconds = 40.25 MB/sec

遅いと思ってたけど、ここ見るとそうでもないみたいだな。
UT2003とかでテクスチャレベルを最高にするとテクスチャ読み込むのが遅すぎてサーバ側から切断される。
これはメモリが足りないせいなのかな。256しか積んでないからな。

145:login:Penguin
03/01/10 11:40 iyykYYz/
cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: QUANTUM Model: ATLAS10K3_18_WLS Rev: 020K
Type: Direct-Access ANSI SCSI revision: 03

hdparm -tT /dev/sda
/dev/sda:
Timing buffer-cache reads: 128 MB in 0.17 seconds =752.94 MB/sec
Timing buffered disk reads: 64 MB in 1.27 seconds = 50.39 MB/sec

146:login:Penguin
03/01/12 22:02 vg6JVWvq
安定しないため、あえてスピード落としてる人っていますか？

ウチだと
80芯ケーブル
hda: WDC WD400AB-00BVA0(40ギガ)
hdb: ST340810A(40ギガ)
40芯ケーブル
hdc: cdrom
で、1日1回完全フリーズ、たまに突然再起動。

80芯ケーブル
hda: ダミーの850Mボロディスク
hdb: ST340810A
40芯ケーブル
hdc: cdrom
hdd: WDC WD400AB-00BVA0
で、安定です。

hdaのWDC WD400AB-00BVA0をumda2くらいに落としてやれば安定するような気がす
るのですが。

電源の最悪値はとりあえず置いておいて下さい。



147:山崎渉
03/01/15 11:26 /OP2L6bf
（＾＾）

148: ◆GarNeT/IDA
03/01/23 13:04 Ow2BQYIc
/dev/hda:

Model=FUJITSU MPG3409AT E, FwRev=82C4, SerialNo=VH06T170K5AM
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.60 seconds = 80.00 MB/sec
Timing buffered disk reads: 64 MB in 2.49 seconds = 25.70 MB/sec

149:宗男の秘書 ◆MUNEOH/q9U
03/01/26 17:14 XMVXpT94
/dev/hdb:

Model=FUJITSU MPF3204AT, FwRev=0028, SerialNo=05086825
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40031712
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 1 2 3 4 5

Timing buffer-cache reads: 128 MB in 0.32 seconds =400.00 MB/sec
Timing buffered disk reads: 64 MB in 2.78 seconds = 23.02 MB/sec

2.4.20 + Con Kolivas patch for 2.4.20 + ReiserFS
これからhdparmで性能をアップしていくぞ

150:login:Penguin
03/01/26 20:55 ahNjS9Yg
>>148
バッファキャッシュの値が小さすぎるような…
hdpram実行時にsuspicious云々なメッセージ出ませんでした？


151:login:anonymous
03/01/26 21:28 RB0X8qDO
マシン：EPIA-C800 MEM:256M
OS：DEBIAN 3.0

/dev/hdb:

Model=MAXTOR 4K080H4, FwRev=A08.1500, SerialNo=674117721182
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=2000kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301487
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=disabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.96 seconds = 65.31 MB/sec
Timing buffered disk reads: 64 MB in 8.93 seconds = 7.17 MB/sec

＋＋＋＋＋＋＋＋＋＋＋＋＋＋＋

EDENって６６MがMAXでしたっけ・・・？１００まで使えたような気がしたんですが。
まぁ用途が家鯖なので全然問題ないんですが（笑

152:login:anonymous
03/01/26 21:29 RB0X8qDO
もう１台

マシン：DURON750+K7SEM
OS：赤帽８．０

/dev/hda:

Model=Maxtor 2F040L0, FwRev=VAM51JJ0, SerialNo=F12B8AKE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80293248
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 1.03 seconds =123.89 MB/sec
Timing buffered disk reads: 64 MB in 2.17 seconds = 29.49 MB/sec

153:login:anonymous
03/01/26 21:30 RB0X8qDO
上のマシンのもう１台のHDD

/dev/hdb:

Model=IC35L060AVER07-0, FwRev=ER6OA44A, SerialNo=SZ0SZ062567
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1: 2 3 4 5

Timing buffer-cache reads: 128 MB in 1.04 seconds =122.73 MB/sec
Timing buffered disk reads: 64 MB in 2.64 seconds = 24.27 MB/sec

154:login:Penguin
03/01/26 21:30 wlra5F/E
$ hddparm -tT
bash: hddparm: command not found

155:初期設定まんま
03/01/27 08:45 0WB64lwM
[root@localhost root]# /sbin/hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 98196H8, FwRev=ZAH814Y0, SerialNo=V80SXMXC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160045200
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 *udma4 udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 0: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 0.72 seconds =178.58 MB/sec
Timing buffered disk reads: 64 MB in 2.28 seconds = 28.03 MB/sec


156:148 ◆garnetkKQ2
03/01/31 19:43 dDR/5UKJ
>>150
でませんでしたよ～。

もう一度やってみますた。
Timing buffer-cache reads: 128 MB in 1.63 seconds = 78.53 MB/sec
Timing buffered disk reads: 64 MB in 2.25 seconds = 28.44 MB/sec

157:login:Penguin
03/02/16 00:11 LjDtqsXB
nForce2マザー(K7N2G-L)買ったんでやってみました。

VineSeed標準のkernel-2.4.20-0vl14だと

/dev/hda:
Timing buffered disk reads: 64 MB in 18.20 seconds = 3.52 MB/sec

という悲惨な状態だったのでいろいろ調べた結果、カーネルにACパッチの
patch-2.4.21-pre4-ac4.bz2をあてて、カーネルパラメータに
ide0=ata66を指定することで

/dev/hda:
Timing buffered disk reads: 64 MB in 1.80 seconds = 35.56 MB/sec

まで出ました。感動。

158:login:Penguin
03/03/21 17:39 6s6tsuw3
VP_IDE: VIA vt82c586b (rev 41) IDE UDMA33 controller on pci00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
hda: ST38410A, ATA DISK drive
hda: 16841664 sectors (8623 MB) w/512KiB Cache, CHS=16708/16/63, UDMA(33)

# hdparm -i /dev/hda
/dev/hda:
Model=ST38410A, FwRev=3.03, SerialNo=6CS1JE84
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=512kB, MaxMultSect=32, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=16841664
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

# hdparm -m16 -c1 -u1 -d1 -tT /dev/hda
/dev/hda:
setting 32-bit I/O support flag to 1
setting multcount to 16
setting unmaskirq to 1 (on)
setting using_dma to 1 (on)
multcount = 16 (on)
I/O support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
Timing buffer-cache reads: 128 MB in 3.13 seconds = 40.89 MB/sec
Timing buffered disk reads: 64 MB in 5.31 seconds = 12.05 MB/sec

159:login:Penguin
03/03/21 18:11 flz8uT9g
# hdparm -itT /dev/hda

/dev/hda:

Model=TOSHIBA MK3004GAH, FwRev=JB001A, SerialNo=13830056T
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=58595040
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.20 seconds =106.67 MB/sec
Timing buffered disk reads: 64 MB in 4.17 seconds = 15.35 MB/sec


160:login:Penguin
03/03/21 22:11 0UpeekfY
/dev/hda:
Model=Maxtor 6Y080L0, FwRev=YAR41VW0, SerialNo=Y3HXS84E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160086528
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ataATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6 ATA-7

Timing buffer-cache reads: 128 MB in 0.34 seconds =376.47 MB/sec
Timing buffered disk reads: 64 MB in 1.33 seconds = 48.12 MB/sec


161:login:Penguin
03/04/15 18:27 I8lYX1jC
/dev/hda:

Model=Maxtor 5T060H6, FwRev=TAH71DP0, SerialNo=
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117187500
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 0: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 1.78 seconds = 35.96 MB/sec


162:山崎渉
03/04/17 12:13 KRn99/cy
（＾＾）

163:山崎渉
03/04/20 06:08 xFRXxEWb
　　 ∧＿∧
　　（　　＾＾ ）＜ ぬるぽ（＾＾）

164: ◆garnetGnNk
03/05/13 10:44 hzndneRN
ぉぉ？

/dev/hda:

Model=FUJITSU MPG3409AT E, FwRev=82C4, SerialNo=VH06T170K5AM
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80063424
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 1.09 seconds =117.43 MB/sec
Timing buffered disk reads: 64 MB in 18.53 seconds = 3.45 MB/sec

165:名無しさん@Eｍａｃｓ
03/05/15 12:35 myPKxNw+
>163
ｶﾞｯ

>164
MPG3049ATE 。。。ｶﾞｸｶﾞｸﾌﾞﾙﾌﾞﾙ｡｡｡


166:山崎渉
03/05/22 02:17 p4opmoqv
━―━―━―━―━―━―━―━―━[JR山崎駅（＾＾）]━―━―━―━―━―━―━―━―━―

167:山崎渉
03/05/28 16:56 3t6i6zxR
　　　 　∧＿∧
ﾋﾟｭ.ｰ　(　　＾＾ ） ＜これからも僕を応援して下さいね（＾＾）。
　　＝〔~∪￣￣〕
　　＝ ◎―◎ 　　　　　　　　　　　　　　　　　　　　　山崎渉

168:山崎 渉
03/07/15 11:31 2JhhXBQM

　__∧＿∧_
　|（　　＾＾ ）|　＜寝るぽ（＾＾）
　|＼⌒⌒⌒＼
　＼ |⌒⌒⌒~|　　　　　　　　　山崎渉
　　 ~￣￣￣￣

169:login:Penguin
03/07/16 07:55 ocabZ7Sv
/dev/hda:

Model=ST3160023A, FwRev=3.06, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2: 1 2 3 4 5 6

Timing buffer-cache reads: 128 MB in 1.07 seconds =119.63 MB/sec
Timing buffered disk reads: 64 MB in 1.17 seconds = 54.70 MB/sec


170:login:Penguin
03/07/16 21:22 nLcaJQSH
>>123
やったけどならなかったよ？

171:login:Penguin
03/07/17 23:31 6vnV9sJK
/dev/hda:

Model=IC35L080AVVA07-0, FwRev=VA4OA52A, SerialNo=VNC402A4GGNWAA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160836480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

Timing buffer-cache reads: 128 MB in 0.87 seconds =147.13 MB/sec
Timing buffered disk reads: 64 MB in 1.42 seconds = 45.07 MB/sec

172:login:Penguin
03/07/22 05:05 I3nBCmGh
Abit NF7-SのSATA(SilliconImage3112A)接続

Model=WDC WD360GD-00FNA0
Timing buffer-cache reads: 128 MB in 0.23 seconds =556.52 MB/sec
Timing buffered disk reads: 64 MB in 1.17 seconds = 54.70 MB/sec

Model=Maxtor 6Y060L0 (SERILLEL2利用)
Timing buffer-cache reads: 128 MB in 0.23 seconds =556.52 MB/sec
Timing buffered disk reads: 64 MB in 1.34 seconds = 47.76 MB/sec

hdg: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq
ってのがコンソールにワンサカでてくるな。
siimage.cで#if 1で括ってあるprintk()を取っ払ってしまえば良さげではあるが．．


173:login:Penguin
03/07/22 06:54 i5QAQTAY
=== [ ▼PR ] =========================================================
獲得ページにて毎日ポイント獲得！広告すると毎日のポイント増えるかも！？
URLﾘﾝｸ(wwa.irias.co.jp)
======================================================== [ ▲PR ] ====


174:ぼるじょあ ◆yBEncckFOU
03/08/02 05:14 +QUfMouI
　　　 　∧＿∧　 ∧＿∧
ﾋﾟｭ.ｰ　（　 ・３・） (　　＾＾ ） ＜これからも僕たちを応援して下さいね（＾＾）。
　　＝〔~∪￣￣￣∪￣￣〕
　　＝ ◎―――◎ 　　　　　　　　　　　　　　　　　　　　　山崎渉&ぼるじょあ

175:login:Penguin
03/09/11 14:16 sY+OAyIi
Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y2VTRHCE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160086528
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 0.13 seconds =984.62 MB/sec
Timing buffered disk reads: 64 MB in 1.13 seconds = 56.64 MB/sec

176:login:Penguin
03/09/12 16:27 GWYQvEI8
# hdparm -tT /dev/hda

/dev/hda:
read() failed: Input/output error
Timing buffered disk reads: read() failed: Input/output error

・・・(´Д｀；)

177:login:Penguin
03/09/12 19:31 aTyG287s
# hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.22 seconds =581.82 MB/sec
止まってしまった、、

% ps auxww|grep hdparm
root 31075 0.0 0.1 2352 1468 pts/1 D 18:26 0:00 /sbin/hdparm -tT /dev/hda
どうすればいいんだ??

178:login:Penguin
03/10/02 00:25 xW6QM91G
Dで止まったら、お手上げさぁね。

179:
03/10/04 09:16 Nfmh/6DN
>>177-178
kill してもダメ?

180:にゃんまげ太郎
03/12/02 15:11 E/+Z5ele
/dev/hda:

Model=FUJITSU M2724TA, FwRev=7604, SerialNo=06115464
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=3162/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=3162/16/63, CurSects=3187296, LBA=yes, LBAsects=3187836
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 *mdma2
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3

Timing buffer-cache reads: 128 MB in 2.62 seconds = 48.85 MB/sec
Timing buffered disk reads: 64 MB in 18.30 seconds = 3.50 MB/sec

181:login:Penguin
03/12/03 14:29 Fo5Xevvy
遅い(ﾟДﾟ)ｺﾞﾙｧ

/dev/hde:

Model=HDS722512VLSA80, FwRev=V33OA60A, SerialNo=VNRC3EC3C415DK
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7938kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=241254720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing buffer-cache reads: 1632 MB in 2.00 seconds = 814.90 MB/sec
Timing buffered disk reads: 96 MB in 3.01 seconds = 31.91 MB/sec


182:login:Penguin
03/12/05 02:08 59Oj9Tqs
1年半前のノートだからあまり速くない
/dev/hda:

Model=TOSHIBA MK4018GAP, FwRev=M0.03 A, SerialNo=12R64684T
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=46
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78140160
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 648 MB in 2.01 seconds = 322.60 MB/sec
Timing buffered disk reads: 64 MB in 3.07 seconds = 20.87 MB/sec


183:Seagateマンセー
03/12/22 21:45 3ytf6VG9
/dev/hda:

Model=ST340016A, FwRev=3.05, SerialNo=3HS0CVGL
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 1020 MB in 2.00 seconds = 510.00 MB/sec
Timing buffered disk reads: 124 MB in 3.04 seconds = 40.79 MB/sec

184:Seagateマンセー
03/12/22 21:45 3ytf6VG9
/dev/hdb:

Model=ST380011A, FwRev=3.04, SerialNo=3JV00Q8V
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing buffer-cache reads: 1004 MB in 2.00 seconds = 502.00 MB/sec
Timing buffered disk reads: 168 MB in 3.01 seconds = 55.81 MB/sec

185:login:Penguin
03/12/22 21:46 3ytf6VG9
＿|￣|○
そこまで速いというわけでもなかったのね…

186:login:Penguin
04/01/17 23:43 RKIrLYDw
Model=IC35L080AVVA07-0, FwRev=VA4OA52A, SerialNo=VNC402A4CP9LRA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=160836480
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

* signifies the current active mode

Timing buffer-cache reads: 1520 MB in 2.00 seconds = 760.00 MB/sec
Timing buffered disk reads: 138 MB in 3.04 seconds = 45.39 MB/sec
なぜか udma3 udma4 udma5 が出ないけど，UDMA(100)とdmesgには出てる
kernel 2.4.22で，dmesgには
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
hda: 160836480 sectors (82348 MB) w/1863KiB Cache, CHS=10011/255/63, UDMA(100)
とあるんだけども。


187:login:Penguin
04/01/20 02:51 W3E7xBCZ
Model=WDC WD740GD-00FLA0, FwRev=21.08U21, SerialNo=WD-WMAKE1006441
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:
Timing buffer-cache reads: 2104 MB in 2.00 seconds = 1052.00 MB/sec
Timing buffered disk reads: 178 MB in 3.01 seconds = 59.14 MB/sec

Model=ST3120026AS, FwRev=3.05, SerialNo=3JT0LQ15
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234441648
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:
Timing buffer-cache reads: 2116 MB in 2.00 seconds = 1058.00 MB/sec
Timing buffered disk reads: 74 MB in 3.00 seconds = 24.67 MB/sec


Seagageだめぽ

188:login:Penguin
04/01/20 06:04 /aP5txjp
# /sbin/hdparm -tT /dev/hda
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.06 seconds =120.75 MB/sec
Timing buffered disk reads: 64 MB in 2.11 seconds = 30.33 MB/sec
# cat /proc/ide/hda/model
ACCUSYS ACS7500 1.2


189:login:Penguin
04/02/01 19:56 AMl1hFRp
Model=Maxtor 6Y120L0, FwRev=YAR41BW0, SerialNo=Y3JAZLLE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=240121728
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):

* signifies the current active mode

Timing buffer-cache reads: 3152 MB in 2.00 seconds = 1576.00 MB/sec
Timing buffered disk reads: 158 MB in 3.01 seconds = 52.49 MB/sec


190:login:Penguin
04/02/27 01:20 UUOmZDvD
/dev/hdb:

Model=IBM-DTLA-307020, FwRev=TX3OA50C, SerialNo=YHDYHT6F813
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=40188960
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

Timing buffer-cache reads: 2892 MB in 2.00 seconds = 1446.00 MB/sec
Timing buffered disk reads: 106 MB in 3.03 seconds = 34.98 MB/sec


191:login:Penguin
04/02/27 01:36 JZQi2dgV
/dev/sda:
Timing buffer-cache reads: 656 MB in 2.01 seconds = 326.58 MB/sec
Timing buffered disk reads: 48 MB in 3.02 seconds = 15.90 MB/sec
USB接続のディスク
本体にUSB1.1用ポートもあるが、恐くて試す気にはならない

192:login:Penguin
04/03/20 23:16 q8sPqx2g
/dev/hda:

Model=ST3120026A, FwRev=3.16, SerialNo=3JT0HTQN
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234375000
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

/dev/hda:
Timing buffer-cache reads: 2368 MB in 2.00 seconds = 1184.18 MB/sec
Timing buffered disk reads: 168 MB in 3.02 seconds = 55.58 MB/sec


193:login:Penguin
04/04/26 09:24 6IcgBNQo
アゲ

194:login:Penguin
04/04/26 23:46 1ND8tNEF
$ /sbin/hdparm -tT /dev/hda
/dev/hda: Permission denied


195:login:Penguin
04/04/26 23:50 1ND8tNEF
/dev/hda:
Timing buffer-cache reads: 128 MB in 1.44 seconds = 88.89 MB/sec
Timing buffered disk reads: 64 MB in 15.61 seconds = 4.10 MB/sec
$ cat /proc/ide/hda/model
Maxtor 6Y200P0
みんな速いなぁ

196:191
04/04/27 00:13 hW9dvw/i
USB1.1接続にして測定してみたぞ
/dev/sdc:
Timing buffer-cache reads: 700 MB in 2.01 seconds = 348.83 MB/sec
Timing buffered disk reads: 4 MB in 4.24 seconds = 966.64 kB/sec

はじめはうかつにも曲聞きながら(USB Audio,48kHz 16bit)チャレンジしたら
I/O Error となってしまった。曲を止めて気をとりなおしてチャレンジ

197:login:Penguin
04/04/28 21:02 hJLArAS4
$ cat /proc/ide/hda/model
FUJITSU MHT2040AT SP

$ cat /proc/ide/hdc/model
UJDA750 DVD/CDRW



198:197
04/04/28 21:05 hJLArAS4
/dev/hda:
Timing buffer-cache reads: 752 MB in 2.00 seconds = 375.12 MB/sec
Timing buffered disk reads: 82 MB in 3.00 seconds = 27.30 MB/sec


199:名無しさん＠お腹いっぱい
04/04/28 23:12 DRMgIbr2
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.38 seconds =336.84 MB/sec
Timing buffered disk reads: 64 MB in 1.13 seconds = 56.64 MB/sec


200:login:Penguin
04/04/28 23:48 yxz9XbxE
# cat /proc/ide/hda/model
Maxtor 6Y080L0
/dev/hda:
Timing buffer-cache reads: 128 MB in 0.46 seconds =278.26 MB/sec
Timing buffered disk reads: 64 MB in 1.14 seconds = 56.14 MB/sec


201:login:Penguin
04/04/29 00:18 o9I+Kw0G
# cat /proc/ide/hda/model
ST3120026A
/dev/hda:
Timing buffer-cache reads: 1648 MB in 2.00 seconds = 823.18 MB/sec
Timing buffered disk reads: 140 MB in 3.04 seconds = 46.04 MB/sec

202:login:Penguin
04/04/29 01:38 lbw9OBWT
# cat /proc/ide/hda/model
Maxtor 6Y080L0

/dev/hda:
Timing buffer-cache reads: 1124 MB in 2.00 seconds = 562.00 MB/sec
Timing buffered disk reads: 172 MB in 3.01 seconds = 57.14 MB/sec

203:login:Penguin
04/04/29 11:20 NX2S7b8D
FUJITSU MPB3032ATU,ATA DISK Drive

/dev/hda:
Timing buffer-cache reads: 128 MB in 10.14 seconds = 12.62 MB/sec
Timing buffered disk reads: 64 MB in 22.72 seconds = 2.82 MB/sec

204:login:Penguin
04/05/01 16:11 rQ3OkBYf
cat /proc/ide/hda/model
Maxtor 6Y060L0

/dev/hda
Timing buffer-cache reads: 1732 MB in 2.00 seconds = 866.00 MB/sec
Timing buffered disk reads: 146 MB in 3.04 seconds = 48.11 MB/sec

遅いのか早いのかよくわかりません

205:login:Penguin
04/05/22 16:33 affgRXsr
/dev/hda:

Model=HDS722516VLAT80, FwRev=V34OA60A, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=7938kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing buffer-cache reads: 424 MB in 2.01 seconds = 211.40 MB/sec
Timing buffered disk reads: 136 MB in 3.02 seconds = 45.10 MB/sec


206:login:Penguin
04/05/22 16:34 affgRXsr
/dev/hdc:

Model=ST3160023A, FwRev=3.06, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing buffer-cache reads: 440 MB in 2.00 seconds = 219.59 MB/sec
Timing buffered disk reads: 106 MB in 3.04 seconds = 34.90 MB/sec


207:login:Penguin
04/06/27 22:35 cjacHE9B
hda と hdcでだいぶ違うのをハケーン。
DMA on なんだけど。

/dev/hda:

Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y288LDDE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156250000
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 0.37 seconds =346.00 MB/sec
Timing buffered disk reads: 64 MB in 5.86 seconds = 10.92 MB/sec

208:login:Penguin
04/06/27 22:35 cjacHE9B
/dev/hdc:

Model=Maxtor 6Y080L0, FwRev=YAR41BW0, SerialNo=Y2875BJE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156250000
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null): 1 2 3 4 5 6 7

Timing buffer-cache reads: 128 MB in 0.36 seconds =354.62 MB/sec
Timing buffered disk reads: 64 MB in 1.13 seconds = 56.45 MB/sec

209:login:Penguin
04/07/04 11:02 M3VVZWpG
# cat /proc/ide/hda/model
HITACHI_DK23FB-40

# hdparm -tT
Timing buffer-cache reads : 128MB in 0.84 seconds =152.38 MB/sec
Timing buffered disk reads: 64MB in 13.25 seconds = 4.83 MB/sec


210:login:Penguin
04/07/04 13:33 1zxrVlAj
Model=WDC WD740GD-00FLA0, FwRev=21.08U21, SerialNo=WD-WMAKE1006441
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 1924 MB in 2.00 seconds = 961.18 MB/sec
Timing buffered disk reads: 204 MB in 3.02 seconds = 67.60 MB/sec


211: ◆Zsh/ladOX.
04/07/04 19:01 BHrpEmCI
>>210
漏れもﾗﾌﾟﾀｿ2使ってるけどその位の速度。
速くて快適だ…

# hdparm -tiT /dev/hde

/dev/hde:

Model=WDC WD740GD-00FLA0, FwRev=21.08U21, SerialNo=WD-WMAKE10603XX
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing buffer-cache reads: 2072 MB in 2.00 seconds = 1035.12 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.18 MB/sec

212:ThinkPad 570
04/07/05 20:26 AlS/ZVbg
HITACHI_DK23DA_16N

Timing buffer-cache reads: 128MB in 1.44 seconds = 88.89 MB/sex
Timing buffered disk reads: 64MB in 4.59 seconds = 13.94 MB/sec

213:login:Penguin
04/07/06 20:58 FqTqA7xx
FUJITSU MAS3367NP

Timing buffer-cache reads: 4044MB in 2.00 seconds = 2021.30 MB/sex
Timing buffered disk reads: 226MB in 3.01 seconds = 75.04 MB/sec

214:login:Penguin
04/07/06 23:00 smyET8Ni
>>212
>>213
Timing buffer-cacheの行の単位がMB/sexになってるぞ!!

215:logon:windows
04/07/10 12:16 JBxFliL3
'hddparm' は、内部コマンドまたは外部コマンド、
操作可能なプログラムまたはバッチ ファイルとして認識されていません。

216:login:Penguin
04/07/21 14:05 lMuFrjOX
# cat /proc/ide/hda/model
IBM-DTTA-350840

# /sbin/hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.98 seconds =130.61 MB/sec
Timing buffered disk reads: 64 MB in 6.21 seconds = 10.31 MB/sec

遅いなぁ・・・P3-500じゃこんなものか

217:login:Penguin
04/07/27 20:11 iBM75hGT
Timing buffer-cache reads: 3420 MB in 2.00 seconds = 1709.41 MB/sec
Timing buffered disk reads: 192 MB in 3.00 seconds = 63.92 MB/sec

速いのかな?


218:login:Penguin
04/07/27 20:30 FGsTH/4M
>>217
チップセット何？

219:217
04/07/27 20:57 iBM75hGT
>218
ICH5 S-ATAなHDD


220:login:Penguin
04/07/27 21:09 AyEVRNqe
$ cat /proc/ide/hda/model
ST340810A
$ /sbin/h
halt hwclock
$ sudo apt-get install hdparm
[...]
Setting up hdparm (4.5-1.2) ...

$ sudo /sbin/hdparm -tT /dev/hda

/dev/hda:
Timing buffer-cache reads: 128 MB in 1.96 seconds = 65.31 MB/sec
Timing buffered disk reads: 64 MB in 9.50 seconds = 6.74 MB/sec

221:login:Penguin
04/08/26 03:01 WYFof0ZU
]# hdparm -tiT /dev/hda

/dev/hda:

Model=HTS726060M9AT00, FwRev=MH4OA68A, SerialNo=MRH401M4G5JHZB
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7877kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=117210240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing buffer-cache reads: 1984 MB in 2.00 seconds = 993.14 MB/sec
Timing buffered disk reads: 110 MB in 3.03 seconds = 36.31 MB/sec


222:login:Penguin
04/08/28 13:56 yEv2JopM
iオプション付けた方が見栄えするな

223:216
04/09/18 18:31:45 LQFrKIPy
CPUをP3-500からCeleron 500に変えたんでもう一度晒し。
# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=IBM-DTTA-350840, FwRev=T55OA73A, SerialNo=WE0WEH11545
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=467kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=16514064
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 1.64 seconds = 78.05 MB/sec
Timing buffered disk reads: 64 MB in 6.75 seconds = 9.48 MB/sec

FSBの差は大きいな。

224:login:Penguin
04/09/20 23:17:46 kkqOBezI
Virtual マシンに入れた Fedora Core 1

$ sudo /sbin/hdparm -tiT /dev/hda
Password:

/dev/hda:

Model=Virtual HD, FwRev=1. 1, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=512, ECCbytes=0
BuffType=DualPortCache, BuffSize=64kB, MaxMultSect=128, MultSect=128
CurCHS=33288/16/63, CurSects=33554304, LBA=yes, LBAsects=33554304
IORDY=on/off, tPIO={min:333,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no

* signifies the current active mode

Timing buffer-cache reads: 496 MB in 1.99 seconds = 249.25 MB/sec
Timing buffered disk reads: 44 MB in 3.06 seconds = 14.38 MB/sec

225:216
04/09/28 20:07:54 /8cKNkSa
i840+P3-500MHzマシン

# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=Maxtor 90680D4, FwRev=PAS23B15, SerialNo=V417RWVA
Config={ Fixed }
RawCHS=13176/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=DualPortCache, BuffSize=256kB, MaxMultSect=16, MultSect=16
CurCHS=13176/16/63, CurSects=13281408, LBA=yes, LBAsects=13281408
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.93 seconds =137.63 MB/sec
Timing buffered disk reads: 64 MB in 5.18 seconds = 12.36 MB/sec

226:login:Penguin
04/10/04 03:35:18 +I4jJv/F
玄人志向のATA133RAID-PCI2につないだHDS722516VLAT80(非RAID)

/dev/sda:
Timing buffer-cache reads: 128 MB in 1.27 seconds =100.79 MB/sec
Timing buffered disk reads: 64 MB in 1.92 seconds = 33.33 MB/sec

カードのBIOSではUDMA5だけどATA33で飽和してるっぽい。
scsi認識だから-iで情報見られないし、-d1は効かないしなぁ。

227:login:Penguin
04/10/16 20:06:09 KQkmWF+V
IC35L180AVV207-1
Timing buffer-cache reads: 1092 MB in 2.00 seconds = 544.72 MB/sec
Timing buffered disk reads: 156 MB in 3.05 seconds = 51.09 MB/sec

Maxtor 6Y200P0
Timing buffer-cache reads: 1048 MB in 2.00 seconds = 524.08 MB/sec
Timing buffered disk reads: 174 MB in 3.02 seconds = 57.62 MB/sec

まぁこんなもんか。

>>213 の MAS とか >>217 の Raptor(?) とかはやっぱり桁違いに速い
ですね。

今年発表された各社の威信を賭けたハイエンドSCSI新モデル群は
何処まで逝くか楽しみですな。

228:login:Penguin
04/11/29 01:11:41 OHYE34d1
/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ST313620A, FwRev=3.07, SerialNo=7BW11BTT
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=26692776
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 1.16 seconds =110.34 MB/sec
Timing buffered disk reads: 64 MB in 2.56 seconds = 25.00 MB/sec

pentium2 450x2 + 初代BarracudaATA 13.6GB

229:記念真紀子
04/12/09 23:54:50 lWm7XnM7
DellPowerEdge400SC+FedoraCore1+linux-2.4.26

/dev/hdb:

Model=ST3200822A, FwRev=3.01, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing buffer-cache reads: 2472 MB in 2.00 seconds = 1236.00 MB/sec
Timing buffered disk reads: 186 MB in 3.00 seconds = 62.00 MB/sec

230:76
04/12/10 23:15:40 e3/dWnM9
同じノートをまだ使っているが
半年ほど前にHDDを換えてみた(40G→80G)
回転数も上がったから多少は速くなっているかも
/dev/hda:

Model=HTS548080M9AT00, FwRev=MG4OA53A, SerialNo=MRL422L4GK498B
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7877kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 664 MB in 2.00 seconds = 331.55 MB/sec
Timing buffered disk reads: 110 MB in 3.05 seconds = 36.04 MB/sec

231:login:Penguin
04/12/17 00:35:35 Q3z0jJ+F
i815 + PenIII-S1.4GHz + linux-2.6.9-gentoo-r6
静かで涼しい、俺の大好きなHDD　現在25°C
/dev/hda:

Model=ST340015A, FwRev=3.01, SerialNo=5LA7VAT5
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing cached reads: 624 MB in 2.01 seconds = 311.11 MB/sec
Timing buffered disk reads: 130 MB in 3.02 seconds = 43.02 MB/sec

232:login:Penguin
04/12/22 02:30:23 zF3llWza
薔薇5400っすか

233:login:Penguin
05/01/11 19:33:17 jgQC2NXl
/dev/hda:

Model=IBM-DJNA-351520, FwRev=J56OA30K, SerialNo=G80GLWHN168
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=34
BuffType=DualPortCache, BuffSize=430kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=30033360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-4 T13 1153D revision 17: 1 2 3 4

Timing buffer-cache reads: 128 MB in 1.34 seconds = 95.52 MB/sec
Timing buffered disk reads: 64 MB in 4.42 seconds = 14.48 MB/sec

234:login:Penguin
05/01/23 22:49:42 o7FAQxHE
/dev/hda:

Model=HDS728040PLAT20, FwRev=PF1OA21B, SerialNo=PFD112S1RWBWUD
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=51
BuffType=DualPortCache, BuffSize=1719kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: Reserved:

* signifies the current active mode

Timing cached reads: 1328 MB in 2.00 seconds = 663.44 MB/sec
Timing buffered disk reads: 148 MB in 3.03 seconds = 48.87 MB/sec

235:login:Penguin
05/01/23 23:15:18 3lhJV5IM
model: HDS722512VLAT80
/dev/hda:
Timing buffer-cache reads: 628 MB in 2.00 seconds = 314.00 MB/sec
Timing buffered disk reads: 174 MB in 3.02 seconds = 57.62 MB/sec

model: Maxtor 6Y120P0
/dev/hdb:
Timing buffer-cache reads: 620 MB in 2.00 seconds = 310.00 MB/sec
Timing buffered disk reads: 144 MB in 3.03 seconds = 47.52 MB/sec

model: Maxtor 6Y120P0
/dev/hdd:
Timing buffer-cache reads: 620 MB in 2.00 seconds = 310.00 MB/sec
Timing buffered disk reads: 146 MB in 3.01 seconds = 48.50 MB/sec

３台とも静穏モードだけど、hdaの日立（IBM）は設計が新しいだけあって速いみたいだな。
ソフトウェアraidドライバとかnfsとかsambaとか動かしたまま

236:login:Penguin
05/01/25 21:19:46 xOZFV118
# cat /proc/ide/hda/model;hdparm -tT /dev/hda
IBM-DTLA-307045

/dev/hda:
Timing buffer-cache reads: 128 MB in 0.93 seconds =137.63 MB/sec
Timing buffered disk reads: 64 MB in 2.57 seconds = 24.90 MB/sec


# cat /proc/ide/hdc/model;hdparm -tT /dev/hdc
WDC WD400BB-75FRA0

/dev/hdc:
Timing buffer-cache reads: 128 MB in 0.93 seconds =137.63 MB/sec
Timing buffered disk reads: 64 MB in 2.73 seconds = 23.44 MB/sec

237:login:Penguin
05/01/27 00:27:17 svgkgAWc
# cat /proc/ide/hda/model;hdparm -tT /dev/hda
Maxtor 6Y120L0

/dev/hda:
Timing cached reads: 1904 MB in 2.00 seconds = 950.72 MB/sec
Timing buffered disk reads: 146 MB in 3.04 seconds = 48.07 MB/sec

238:login:Penguin
05/02/01 22:39:08 irHVdbVR
/dev/hda:

Model=ST380011A, FwRev=8.01, SerialNo=5JVEGW6M
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156295279
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing cached reads: 2536 MB in 2.00 seconds = 1267.56 MB/sec
Timing buffered disk reads: 166 MB in 3.01 seconds = 55.10 MB/sec

＃　このスレみて自分のドライブが異様に遅いのに気付くまで、
＃　ケーブルが古い４０芯でUDMA-33で動作してるのに気付かなかった
＃
＃　ちなみに同じドライブでこれぐらいだった↓
＃　Timing cached reads: = 250 MB/sec
＃ Timing buffered disk reads: = 28 MB/sec


239:中古格安ディスク
05/02/28 04:46:35 w7Vpyt1I
/dev/hda:

Model=ST36422A, FwRev=1.70, SerialNo=7AC01TSV
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=13228/15/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=256kB, MaxMultSect=16, MultSect=16
CurCHS=13228/15/63, CurSects=12500460, LBA=yes, LBAsects=12500460
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version: 1 2 3 4

* signifies the current active mode

/dev/hda:
Timing cached reads: 532 MB in 2.00 seconds = 266.00 MB/sec
Timing buffered disk reads: 42 MB in 3.03 seconds = 13.86 MB/sec

カタカタうるさいディスク、

240:login:Penguin
05/02/28 04:52:54 YIgGQUqd
僕のｼﾝｺﾊﾟｯﾄﾞでつ。

# hdparm -tT /dev/hda1

/dev/hda1:
Timing cached reads: 620 MB in 2.01 seconds = 308.20 MB/sec
Timing buffered disk reads: 70 MB in 3.04 seconds = 23.01 MB/sec

HDDを買い換えて2ﾏｿしたっす。2ﾏｿ払った成果はあるようです。


241:login:Penguin
05/02/28 22:26:51 jxUmjyKI
/dev/hdd:

Model=QUANTUM FIREBALL EX6.4A, FwRev=A0A.0D00, SerialNo=276903422458
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=13325/15/63, TrkSize=32256, SectSize=21298, ECCbytes=4
BuffType=DualPortCache, BuffSize=418kB, MaxMultSect=16, MultSect=16
CurCHS=13325/15/63, CurSects=12592125, LBA=yes, LBAsects=12592847
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-4 T13 1153D revision 15: 1 2 3 4

* signifies the current active mode

Timing cached reads: 2432 MB in 2.00 seconds = 1214.36 MB/sec
Timing buffered disk reads: 38 MB in 3.03 seconds = 12.54 MB/sec

5年ぐらい前のHDだが、まあ歳相応の性能ってところか。



242:login:Penguin
05/03/01 22:52:55 4CiTp4tI
# hdparm -iTt /dev/hde [~]

/dev/hde:

Model=WDC WD740GD-00FLA1, FwRev=27.08D27, SerialNo=WD-WMAKE1601147
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=74
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=145226112
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

* signifies the current active mode

Timing cached reads: 2096 MB in 2.00 seconds = 1047.11 MB/sec
Timing buffered disk reads: 204 MB in 3.03 seconds = 67.38 MB/sec

なんで cached read がやたら遅いんだろう。

243:login:Penguin
05/03/02 00:24:13 iGyotS9C
# hdparm -tiT /dev/hda

/dev/hda:

Model=QUANTUM FIREBALL ST3.2A, FwRev=A0F.F800, SerialNo=153718315215
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=6256/16/63, TrkSize=32256, SectSize=512, ECCbytes=4
BuffType=DualPortCache, BuffSize=81kB, MaxMultSect=16, MultSect=16
CurCHS=6256/16/63, CurSects=6306048, LBA=yes, LBAsects=6306048
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no
Drive conforms to: device does not report version: 1 2 3

* signifies the current active mode

Timing cached reads: 116 MB in 2.04 seconds = 56.86 MB/sec
Timing buffered disk reads: 28 MB in 3.15 seconds = 8.89 MB/sec


とっても遅いづら。

244:login:Penguin
05/03/07 16:31:25 YpnTrMh/
RAID組んで測っているのは無いんか？

245:login:Penguin
05/03/16 19:53:27 I6NMpJMw
# hdparm -itT /dev/hda

/dev/hda:

Model=TOSHIBA MK2103MAV, FwRev=D0.05 A, SerialNo=97874156
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=4200/16/63, TrkSize=40257, SectSize=639, ECCbytes=21
BuffType=DualPortCache, BuffSize=128kB, MaxMultSect=16, MultSect=16
CurCHS=4200/16/63, CurSects=4233600, LBA=yes, LBAsects=4233600
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3

Timing buffer-cache reads: 128 MB in 5.84 seconds = 21.92 MB/sec
Timing buffered disk reads: 64 MB in 27.53 seconds = 2.32 MB/sec


10年前のPentium120MHzノート+東芝2G+Vine2.5で使ってる自宅鯖。(*´▽`*) ｵｿｰｲ

246:login:Penguin
05/03/23 18:36:51 TDALkra/
hdparm -tT /dev/sda10

/dev/sda10:
Timing buffer-cache reads: 128 MB in 0.13 seconds =984.62 MB/sec
Timing buffered disk reads: 64 MB in 0.78 seconds = 82.05 MB/sec

Vendor: DELL Model: Virtual Disk 0 Rev: V1.0
Type: Direct-Access ANSI SCSI revision: 02



247:login:Penguin
05/03/23 21:46:23 2YotQzhg
hdparm -tiT /dev/hda

/dev/hda:

Model=IC35L120AVVA07-0, FwRev=VA6OA52A, SerialNo=VNC603A6GGEZVA
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1863kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=241254720
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:

* signifies the current active mode

Timing cached reads: 1704 MB in 2.00 seconds = 851.28 MB/sec
Timing buffered disk reads: 126 MB in 3.04 seconds = 41.41 MB/sec

248:login:Penguin
05/03/23 22:35:05 2YotQzhg
hdparm -tiT /dev/hda

/dev/hda:

Model=IBM-DYLA-28100, FwRev=YSAAA23H, SerialNo=VC0VC033424
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=15880/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=459kB, MaxMultSect=16, MultSect=off
CurCHS=15880/16/63, CurSects=16007040, LBA=yes, LBAsects=16007040
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=yes: mode=0x80 (128)
Drive conforms to: ATA-3 X3T10 2008D revision 1: 1 2 3

* signifies the current active mode

Timing cached reads: 232 MB in 2.01 seconds = 115.27 MB/sec
Timing buffered disk reads: 22 MB in 3.04 seconds = 7.24 MB/sec

249:login:Penguin
05/03/25 02:30:03 Whpx7+Zs
/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=Maxtor 91728D8, FwRev=GAS54112, SerialNo=A80BELHC
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=29
BuffType=DualPortCache, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=33750864
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-4 T13 1153D revision 17: 1 2 3 4

* signifies the current active mode

Timing cached reads: 240 MB in 2.00 seconds = 120.00 MB/sec
Timing buffered disk reads: 46 MB in 3.11 seconds = 14.79 MB/sec

250:login:Penguin
05/03/25 13:34:07 5PuW9KV7
/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=HTS548080M9AT00, FwRev=MG4OA53A, SerialNo=MRL442L4GNDMDB
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=7877kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 1384 MB in 2.01 seconds = 690.04 MB/sec
Timing buffered disk reads: 104 MB in 3.00 seconds = 34.61 MB/sec

251:login:Penguin
05/03/26 19:02:50 BMdCxAVh
dev/hdb:
Timing cached reads: 816 MB in 2.00 seconds = 407.86 MB/sec
Timing buffered disk reads: 162 MB in 3.05 seconds = 53.19 MB/sec


252:login:Penguin
05/04/03 20:56:13 wKGOKtF/ BE:124047375-##
$ sudo /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=Virtual HD, FwRev=1. 1, SerialNo=
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=32256, SectSize=512, ECCbytes=0
BuffType=DualPortCache, BuffSize=64kB, MaxMultSect=128, MultSect=128
CurCHS=33288/16/63, CurSects=33554304, LBA=yes, LBAsects=33554304
IORDY=on/off, tPIO={min:333,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
AdvancedPM=no

* signifies the current active mode

Timing buffer-cache reads: 1636 MB in 1.99 seconds = 822.11 MB/sec
Timing buffered disk reads: 92 MB in 3.01 seconds = 30.56 MB/sec

253:login:Penguin
05/05/09 12:41:07 eozLOQmT
Debian:~# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ASI ARAID99 1000 Ver1.00, FwRev=v1.00.47, SerialNo=A020-0272-14001-0000
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:0,rec:0}
PIO modes: pio3 pio4
DMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.94 seconds =136.17 MB/sec
Timing buffered disk reads: 64 MB in 14.16 seconds = 4.52 MB/sec
Debian:~#

254:253
05/05/09 22:35:36 OMfmt8Sy
俺のは遅すぎたみたい。
家でﾊﾟﾗﾒﾀさわってみた


Debian:~# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ASI ARAID99 1000 Ver1.00, FwRev=v1.00.47, SerialNo=A020-0272-14001-0000
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=8
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:0,rec:0}
PIO modes: pio3 pio4
DMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.90 seconds =142.22 MB/sec
Timing buffered disk reads: 64 MB in 1.15 seconds = 55.65 MB/sec
Debian:~#

255: ◆Zsh/ladOX.
05/05/09 22:37:57 cpUgu9s8
漏れもそう思っていたが書かなかった(w

256:login:Penguin
05/05/28 22:44:11 RwCobzrw
Model=ST340015A, FwRev=3.01, SerialNo=5LAJT6PR
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 *udma2 udma3 udma4 udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: device does not report version:

Timing cached reads: 112 MB in 2.01 seconds = 55.76 MB/sec
Timing buffered disk reads: 30 MB in 3.12 seconds = 9.63 MB/sec

なんでこんなに遅いんだろ・・・？
ファーヤーボールでも19MB/secまで出てたのに・・


257:login:Penguin
05/05/29 01:01:26 bkGVVj/s
$ sudo hdparm -tiT /dev/hda

/dev/hda:

Model=ST340810A, FwRev=3.39, SerialNo=5FB2VY20
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: unknown setting WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 2.07 seconds = 61.84 MB/sec
Timing buffered disk reads: 64 MB in 2.46 seconds = 26.02 MB/sec

このスレ見てDMAがOFFになってたのに気づいた。。。
何年気づかずに使ってたんだろう。。。orz

258:login:Penguin
05/05/29 04:30:50 Xq78Sccj
# /sbin/hdparm -itT /dev/hda

/dev/hda:

Model=ST340014A, FwRev=3.06, SerialNo=5JX6TNFS
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=no WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 2:

* signifies the current active mode

Timing cached reads: 2088 MB in 2.00 seconds = 1044.16 MB/sec
Timing buffered disk reads: 166 MB in 3.03 seconds = 54.79 MB/sec


259:login:Penguin
05/06/13 07:36:33 P1YqOEF/
Model=HDS722525VLAT80, FwRev=V36OA63A, SerialNo=VN693ECFE0YJWD
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=7938kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 3596 MB in 2.00 seconds = 1797.37 MB/sec
Timing buffered disk reads: 176 MB in 3.01 seconds = 58.38 MB/sec


260:login:Penguin
05/09/22 20:08:11 sY542jwh
Model=WDC WD135BA, FwRev=16.13M16, SerialNo=WD-WMA02
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=16
DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
CurCHS=17475/15/63, CurSects=16513875, LBA=yes, LBAsects=26406576
tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4

# hdparm -t /dev/hda
/dev/hda:
Timing buffered disk reads: 32 MB in 1.45 seconds =22.10 MB/sec

261:login:Penguin
05/10/03 03:41:14 l911Pi9+
# hdparm -itT /dev/hde

/dev/hde:

Model=IC35L060AVV207-0, FwRev=V22OA63A, SerialNo=VNVB01G2G5H4YE
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1821kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 384 MB in 2.02 seconds = 190.13 MB/sec
Timing buffered disk reads: 72 MB in 3.05 seconds = 23.60 MB/sec

262:login:Penguin
05/10/03 03:42:24 l911Pi9+
# hdparm -itT /dev/hdf

/dev/hdf:

Model=HDS722516VLAT20, FwRev=V34OA6EA, SerialNo=VNR41EC4CR3P4M
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1794kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 320 MB in 2.02 seconds = 158.36 MB/sec
Timing buffered disk reads: 92 MB in 3.01 seconds = 30.55 MB/sec

263:login:Penguin
05/10/04 02:51:11 ILOu3W4O
一つの外付けのケースに入れたドライブ（Toshiba MK8026GAX）を、

1). IEEE1394 で接続した場合

/dev/sda:
Timing cached reads: 528 MB in 2.01 seconds = 262.69 MB/sec
Timing buffered disk reads: 58 MB in 3.12 seconds = 18.59 MB/sec

と、

2). USB2.0 で接続した場合

/dev/sda:
Timing cached reads: 556 MB in 2.00 seconds = 278.00 MB/sec
Timing buffered disk reads: 36 MB in 3.05 seconds = 11.80 MB/sec

とで計測。

物理的にはまったく同じケース＋ドライブだけど、
接続方法が違うだけでこんなに違う。

ちなみに IEEE1394 は VIA OHCI Compliant IEEE 1394 Host Controller、
USB2 は NEC PCI to USB Enhanced Host Controller B1 の、
それぞれ PCI バスに刺したカード経由。

264:login:Penguin
05/10/08 22:24:48 1zbZptqU
2台でSoftware Raid0を組んでみた。

# hdparm -tT /dev/md0

/dev/md0:
Timing cached reads: 3560 MB in 2.00 seconds = 1778.49 MB/sec
Timing buffered disk reads: 412 MB in 3.01 seconds = 136.81 MB/sec

265:login:Penguin
05/10/11 23:19:26 odqTH2pw
$ sudo hdparm -tiT /dev/hda

/dev/hda:

Model=FUJITSU MHT2080AH, FwRev=006C, SerialNo=NP0FT5428V6T
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=8192kB, MaxMultSect=16, MultSect=off
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 2648 MB in 2.00 seconds = 1322.88 MB/sec
Timing buffered disk reads: 102 MB in 3.02 seconds = 33.75 MB/sec


dell inspiron 700m でカキコ
ていうか今ごろ気づいたけど F かよ。。
まぁもれは以前のHDDぶっこわれ事件のときに壊れる前に
ソフマップに売り抜けた勝ち組だからべつにいいけどwww

266:login:Penguin
05/10/14 10:07:55 oZRDIECe
/dev/hda:

Model=HTS548080M9AT00, FwRev=MG4OA53A, SerialNo=MRL455L4JBARTB
Timing cached reads: 1660 MB in 2.00 seconds = 829.95 MB/sec
Timing buffered disk reads: 104 MB in 3.05 seconds = 34.12 MB/sec

/dev/hdc:

Model=PIONEER DVD-RW DVR-K15, FwRev=1.11, SerialNo=
Timing cached reads: 1640 MB in 2.00 seconds = 819.95 MB/sec
Timing buffered disk reads: 10 MB in 3.29 seconds = 3.04 MB/sec


267:login:Penguin
05/10/31 07:07:46 yf1E/KLT
/dev/hda:

Model=HDT722516DLAT80, FwRev=V43OA70A, SerialNo=VD071BTCCT8RSE
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=51
BuffType=DualPortCache, BuffSize=7674kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: Reserved:

* signifies the current active mode

Timing cached reads: 2232 MB in 2.00 seconds = 1115.05 MB/sec
Timing buffered disk reads: 164 MB in 3.01 seconds = 54.57 MB/sec

268:login:Penguin
05/12/15 19:09:36 g5GaQYuq
cat /proc/ide/hda/model
ST380021A

hdparm -tT /dev/hda
Timing cached reads: 1744 MB in 2.00 seconds = 871.95 MB/sec
Timing buffered disk reads: 110 MB in 3.01 seconds = 36.57 MB/sec


269:login:Penguin
05/12/18 02:52:51 aPnD4wMj
cat /proc/ide/hda/model
ST380021A

/sbin/hdparm -tT /dev/hda
Timing cached reads: 1288 MB in 2.00 seconds = 644.00 MB/sec
Timing buffered disk reads: 114 MB in 3.04 seconds = 37.50 MB/sec

270:login:Penguin
05/12/18 03:03:44 wQOSCCil
cat /sys/block/sdb/device/model
9500S-4LP DISK

hdparm -tT /dev/sdb
/dev/sdb:
Timing cached reads: 2768 MB in 2.00 seconds = 1382.83 MB/sec
Timing buffered disk reads: 250 MB in 3.01 seconds = 82.99 MB/sec

271:login:Penguin
06/02/12 12:57:15 XlbqUozm
sage

272:login:Penguin
06/03/06 04:00:21 CBydarvA
/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=HDS722516VLAT20, FwRev=V34OA60A, SerialNo=VNR4GEC4C5G9XK
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=52
BuffType=DualPortCache, BuffSize=1794kB, MaxMultSect=16, MultSect=16
CurCHS=65535/1/63, CurSects=4128705, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:

* signifies the current active mode

Timing cached reads: 552 MB in 2.00 seconds = 276.00 MB/sec
Timing buffered disk reads: 174 MB in 3.00 seconds = 58.00 MB/sec

273:login:Penguin
06/06/07 03:39:02 DX8eaAUn
cat /proc/ide/hda/model
ST3120022A
hdparm -tT /dev/hda
/dev/hda:
Timing cached reads: 4024 MB in 2.00 seconds = 2011.33 MB/sec
Timing buffered disk reads: 156 MB in 3.02 seconds = 51.73 MB/sec

cat /sys/block/sda/device/model
WDC WD740GD-75FL
hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 4064 MB in 2.00 seconds = 2030.88 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.18 MB/sec

274:login:Penguin
06/06/28 18:19:30 cEBx0ZTG
/dev/hda: HDS728080PLAT20（ATA-66）
multcount = 0 (off)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 16383/255/63, sectors = 160836480, start = 0

Timing cached reads: 2596 MB in 2.00 seconds = 1298.20 MB/sec
Timing buffered disk reads: 150 MB in 3.01 seconds = 49.91 MB/sec

>>234 もうあったのか

275:login:Penguin
06/06/28 18:24:08 cEBx0ZTG
setting multcount to 16
setting xfermode to 70 (UltraDMA mode6)
に変更して

Timing cached reads: 2536 MB in 2.00 seconds = 1267.56 MB/sec
Timing buffered disk reads: 150 MB in 3.03 seconds = 49.53 MB/sec

変わらず･･･マルチセクタOff、UDMA4で十分らしい

276:274-275
06/07/06 17:02:07 AJXR/ZQf
dmesgにCRCエラーが出るんでどないなっとんじゃいと思ったら
ケーブル腐ってました･･･

/dev/hda:
Timing cached reads: 2552 MB in 2.00 seconds = 1275.56 MB/sec
Timing buffered disk reads: 174 MB in 3.02 seconds = 57.61 MB/sec

277:login:Penguin
06/07/06 17:32:39 NjI80nyM
ここはHDDの歴史がわかるスレですね

278:login:Penguin
06/07/06 19:01:39 zZ4+gxBv
/sbin/hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 4R060L0, FwRev=RAMC1TU0, S/sbin/hdparm -itT /dev/hda

/dev/hda:

Model=Maxtor 4R060L0, FwRev=RAMC1TU0, SerialNo=R2R9P42E
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=120103200
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: (null):

* signifies the current active mode

Timing cached reads: 1132 MB in 2.01 seconds = 564.39 MB/sec
Timing buffered disk reads: 112 MB in 3.01 seconds = 37.21 MB/sec

ﾃﾗｼｮﾎﾞｽ orz

279:login:Penguin
06/07/07 14:08:22 +/HOu7cX
なんだかしらんが、こんな数字がでたぞ。

# hdparm -tT /dev/sda

/dev/sda:
Timing cached reads: 4180 MB in 1.99 seconds = 2098.48 MB/sec
Timing buffered disk reads: 142 MB in 3.03 seconds = 46.92 MB/sec



280:login:Penguin
06/07/07 16:45:40 /DSIfUx2
# hdparm -tT /dev/hda

/dev/hda:
Timing cached reads: 1760 MB in 2.00 seconds = 878.93 MB/sec
Timing buffered disk reads: 62 MB in 3.04 seconds = 20.42 MB/sec

# cat /proc/ide/hda/model
HTC426060G9AT00

恐怖のX40ユーザーですが、お前らこんにちは。
1.8インチHDDは速度こそこの通りunkoburiburiですが、びっくりするほど衝撃に強いですよ。

281:228
06/07/09 13:02:49 V0YDn35t
/sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ST313620A, FwRev=3.07, SerialNo=7BW11BTT
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=0
BuffType=unknown, BuffSize=512kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=26692776
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4

Timing buffer-cache reads: 128 MB in 0.55 seconds =232.73 MB/sec
Timing buffered disk reads: 64 MB in 2.92 seconds = 21.92 MB/sec

P2-450x2とPC100 SDRAMから、P3-800(133）x2とPC800-45に変更した
結構メモリ速度あがるね

282:login:Penguin
06/07/28 04:58:11 FN6L64FY
cat /sys/block/sda/device/model
WDC WD1600JS-00N
hdparm -tT /dev/sda

/dev/sda:
Timing cached reads: 3128 MB in 2.00 seconds = 1563.46 MB/sec
Timing buffered disk reads: 174 MB in 3.01 seconds = 57.84 MB/sec

283:login:Penguin
06/10/23 05:42:43 xY3UJe7d
linuxhost ~ # cat /sys/block/sda/device/model
Hitachi HDT72503
linuxhost ~ # hdparm -Tt /dev/sda
/dev/sda:
Timing cached reads: 1632 MB in 2.00 seconds = 815.94 MB/sec
Timing buffered disk reads: 220 MB in 3.00 seconds = 73.30 MB/sec

linuxhost ~ # cat /sys/block/sdb/device/model
WDC WD740GD-00FL
linuxhost ~ # hdparm -Tt /dev/sdb
/dev/sdb:
Timing cached reads: 1624 MB in 2.00 seconds = 811.51 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.14 MB/sec

284:login:Penguin
06/10/23 15:27:00 QbahEVTb
ST3250620AS
/dev/sda:
Timing cached reads: 3004 MB in 2.00 seconds = 1501.91 MB/sec
Timing buffered disk reads: 230 MB in 3.00 seconds = 76.56 MB/sec

ST3200822A
/dev/hda:
Timing cached reads: 2996 MB in 2.00 seconds = 1497.91 MB/sec
Timing buffered disk reads: 186 MB in 3.01 seconds = 61.83 MB/sec


285:login:Penguin
06/10/25 18:35:05 NlbtCtlk
Vendor: FUJITSU Model: MAW3300NC Rev: 5803
/dev/sda:
Timing cached reads: 3624 MB in 2.00 seconds = 1811.37 MB/sec
Timing buffered disk reads: 276 MB in 3.02 seconds = 91.31 MB/sec


286:login:Penguin
06/10/25 19:34:55 oiG9vsr0
$ cat /sys/block/sda/device/model
WDC WD740ADFD-00

$ sudo /sbin/hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 4028 MB in 2.00 seconds = 2015.55 MB/sec
Timing buffered disk reads: 250 MB in 3.02 seconds = 82.88 MB/sec

287:285
06/10/25 20:26:10 NlbtCtlk
SEAGATE Model: ST336754LC Rev: D404
でした

288: ◆Zsh/ladOX.
06/10/25 23:26:10 xsHXPrt3
>>286
うわっ、速。

289:228
06/10/28 16:21:49 GjxSaIfF
# /sbin/hdparm -tiT /dev/hda

/dev/hda:

Model=ST320014A, FwRev=3.07, SerialNo=5JZB6NW7
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39102336
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 *udma4
AdvancedPM=no WriteCache=enabled
Drive Supports : Reserved : ATA-1 ATA-2 ATA-3 ATA-4 ATA-5 ATA-6

Timing buffer-cache reads: 128 MB in 0.61 seconds =209.84 MB/sec
Timing buffered disk reads: 64 MB in 2.15 seconds = 29.77 MB/sec

290:login:Penguin
07/01/22 09:05:52 BbiiiCwj
# cat /sys/block/sda/device/model
ST3320620AS

# hdparm -tT /dev/sda
/dev/sda:
Timing cached reads: 3444 MB in 2.00 seconds = 1721.60 MB/sec
Timing buffered disk reads: 206 MB in 3.02 seconds = 68.19 MB/sec


291:login:Penguin
07/01/22 09:19:16 Pbbnsn1N
hdparm -tT /dev/md0

/dev/md0:
Timing cached reads: 3920 MB in 2.00 seconds = 1961.66 MB/sec
Timing buffered disk reads: 396 MB in 3.00 seconds = 131.82 MB/sec

ソフトウェアRAID5でSATAⅡのHDDを3本使用

292:普通すぎてすいません
07/01/23 19:17:02 fVtcwSHW
ST318406LC

/dev/sda:
　Timing cached reads: 　 600 MB in 　2.01 seconds = 298.85 MB/sec
　Timing buffered disk reads: 　132 MB in 　3.02 seconds = 　43.76 MB/sec


293:login:Penguin
07/03/07 03:46:56 wJvE4oyf
/sbin/hdparm -tiT /dev/sda

/dev/sda:
Model=HDT722525DLAT80 , FwRev=V44OA70A, SerialNo= VD041BT4CPHKDE
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=51
BuffType=DualPortCache, BuffSize=7674kB, MaxMultSect=16, MultSect=?16?
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 udma3 udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-7 T13 1532D revision 1: ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

* signifies the current active mode

Timing cached reads: 1332 MB in 2.00 seconds = 665.50 MB/sec
Timing buffered disk reads: 202 MB in 3.03 seconds = 66.78 MB/sec

SATA2にしてぇ…
キャッシュ16M欲しい…
DDR2も…
あああああああああああああああああ新しいマシンくみてえええええええええ！！！！！

294:login:Penguin
07/08/08 15:30:41 tYKYxZ6G
Model=Maxtor 6Y120L0, FwRev=YAR41BW0, SerialNo=Y34ZA1HE

/dev/hda:
Timing cached reads: 1194 MB in 2.00 seconds = 596.89 MB/sec
Timing buffered disk reads: 170 MB in 3.00 seconds = 56.58 MB/sec

まあこんなもんだろ
触れないほど熱いのに41℃とか出る

---

次ページ

最新レス表示

レスジャンプ

類似スレ一覧

スレッドの検索

話題のニュース

おまかせリスト

オプション

しおりを挟む

スレッドに書込

スレッドの一覧

暇つぶし2ch